Short Barrel Rifle Engraving Locations

 

SBR M16

 

 

The ATF requires all short barrel rifles to be engraved with the manufacturers name, city, and state. All of our SBR markings are engraved at a standard size and depth to meet and exceed the required ATF regulations. All SBR markings are engraved using a font designated by the ATF. We will not deviate from this font and size to ensure that all of our work is NFA compliant.

The images below illustrate the standard locations that we engrave these markings.

** Please note that Orion Arms cannot advise nor consult on ATF regulations regarding the use of Trusts names. Recently we have had many customers have their form 1 declined due to the use of the abbreviation RLT in place of Revocable Living Trust. Therefore we will no longer engrave RLT and Revocable Living Trust must be spelled out.

** Polymer receivers can be engraved with our equipment.

Please note: the images shown on this page do not represent the actual font or size of the engraving you will receive.  These are meant to convey SBR engraving locations only.

** We can engrave SBR markings on most rifles.  If you do not see your model listed on this page please email us for more information.

 

AR 15 Locations

** With all of the variations in billet receivers available on the market please specify which brand and model you have.

** Please include a sample of the text to be engraved along with the location of your choosing in your initial email for a price quote.

** 9mm receivers can be engraved. They will require a custom setup to place the engraving on the front of the magwell. If the feed ramp and ejector can be removed the other locations can be used.

Front Magwell

- The maximum characters per line is 16 for this location. This does include spaces.

- Receivers with textured front magwells cannot be engraved.

- The front of the magwell is the only location that does not require a completely stripped lower.

- Fixed stocks and buffer tubes must be removed.

- Collapsible stock buffer tubes can remain but the buttstock, buffer and spring MUST be removed.

** For all calibers other than .223/5.56mm the mag blocks will need to be removed for the front magazine well engraving.

Right Hand  Side - Left Hand Side

** We have built new fixtures that offer easier stripping requirements.

- These locations will now allow the bolt catch, buffer tube, and front take down pin to remain installed.

- The fire control group, selector, rear pin, pistol grip, and all detents and springs will need to be removed.

** Any billet receiver models with advanced bolt release levers or mag release buttons will need to be completely stripped of these parts. These models may not allow engraving in all areas due to their designs.

 

Trigger Guard

- These locations require a completely stripped lower.   This includes the bolt catch assembly.

- The trigger guard area cannot be engraved on billet models with non removable gaurds.

- Maximum characters per line is 16 for the trigger guard location.

** The front takedown pin can remain installed if not easily removable.

** Standard pivoting trigger guards can remain installed if not easily removable.

All AR15 engravings will be re-blackened unless a special request is made ahead of time

 

AK 47 Locations

** Please include a sample of the text to be engraved along with the location of your in your initial email for a price quote.

**Please specify in your initial email whether you are sending a virgin receiver or completed build.

Under Trigger Guard

- This location can only be engraved on virgin receivers.  Trigger guard parts cannot be installed.

- Completed rifles can be engraved forward of the magwell opening on the bottom of the receiver. if you have a side folding stock please let us know in the quote request.

*** All complete rifles will need to have the stock, hand guards and grip removed prior to sending in the rifle. Models with a riveted top cover can leave it in place.

 

HK MP5 / GSG-5 Locations

** Please include a sample of the text to be engraved in your initial email.

- The location shown below is the only location we engrave MP5s and clones with SBR markings.

- Only the right side receiver shell is needed for the GSG-5 SBR engravings.

** Please field strip the MP5 receiver prior to sending it to us for engraving. The cocking handle does not need to be removed.

*** GSG models will require only the rh side plate to be shipped.

 

PS 90 Locations

** Please include a sample of the text to be engraved in your initial email.

- The image shown below illustrates the most common location we engrave for PS90's.   The right side of the receiver can be engraved upon special request.

** Please completely strip the receiver prior to sending it to us for engraving.

 

MCX & MPX

- The RH magwell is the only location we use on these models.

**Please include a sample of the text to be engraved in your initial email.

** Please strip the lower receiver prior to sending it to us for engraving. The grip, hammer and stock must be removed on these models.

 

CZ Scorpion Evo 3

- Below the Mfger name is the location we use on the upper for this model.

**Please include a sample of the text to be engraved in your initial email.

** Please field strip the upper receiver prior to sending it to us for engraving. The grip and mounted accessories must be removed on this model.

 

HK USC Locations

** Please include a sample of the text to be engraved in your initial email.

- The location shown below is the primary location we engrave the HK USC with SBR markings.

- The SBR markings will be centered in a box to match the original HK layout.

** Please field strip the receiver prior to sending it to us for engraving.

- The plastic receivers will leave a light plastic burr. These will need to be removed by the customer

 

SIG 556 SBR Locations

** Please include a sample of the text to be engraved in your initial email.

- The location shown below is the primary location we engrave SIG 556 with SBR markings.

** Please field strip the upper receiver prior to sending it to us for engraving. The handguards and gas system must be removed.

 

UZI Locations

** Please include a sample of the text to be engraved in your initial email.

- The most common loction used by our customers is the bottom of the receiver between the stock rails.

** Please completely strip the receiver prior to sending it to us for engraving.

 

 

 

 

 

 

Yep, ads.

©2006-2017 Orion Arms Mfg. All Rights Reserved
powered by Dala Ad Agency